Used FitzMills - Fitzpatrick Milling Equipment

Stock# 11059359

Used Fitzpatrick Fitzmill Hammer Mill, Model M5A. Vari-speed drive. Serial# 1987. Last used in sanitary pharmaceutical plant.

Stock# 53778001

Used Fitzpatrick Fitzmill, Model VFS-D6A-PCS-LB / VFS D6-PCS-0401 Hammer Mill. XP Controls. Serial# 11839, built 2004.

Stock# 10211226

Used Fitzpatrick Fitzmill Comminuting Machine, Model D. Stainless steel material in contact with product. 3HP. Unit is gravity fed with slanted inlet throat with an opening of 4.75"H X 5.75"W. 6" wide milling chamber with a 10" diameter rotor. Mill Rotor: 16 pivoting blades, plain bars 1" wide X 0.25" thick. Bottom discharge hopper with 7.75" flange, 42.25" above base elevation. Portable carbon steel stand with a base area of 42" X 46". 3HP two-speed v-belt drive, 1750 RPM TEFC motor. Supply power: 115/230V, 60Hz, single phase AC. Bottom sizing screens not included.

Stock# 40425045

Used Fitzpatrick Fitzmill, Model D6A. Stainless steel construction. Pan feed. Driven by 5 HP, 230/460 volt motor. Mounted on stand. Serial# 10770.

Stock# 53162004

Used Fitzpatrick Fitzmill, Model D6. 304 Stainless Steel Contact Parts. (16) Swinging impact/knifes blades, metal tested TS-D2/3/4. Approximately 6" x 11" cutting chamber, gravity feed throat with pan, and bottom screen. 37" discharge height. Driven by 5hp, 3/60/220/440 volt, 1760 rpm motor. Mounted on (4) legs with casters. Serial #4709.

Stock# 53380001

Used Fitzpatrick Fitzmill, Model DAS06, Stainless Steel. (16) Impact/knife fixed stainless steel blades. Approximate 6" x 11" cutting chamber. Driven by a 15hp, 3/60/230/460 volt, 3530 rpm motor. Manual variable speed motor. Infeed hopper with screw feeder. Outboard bearing design. Jacketed top cover. Bottom discharge. Mounted on a carbon steel base with pipe legs. Serial# 8930.

Stock# 53656001

Used Fitzpatrick Fitzmill, Model DASO6 Hammer Mill, Stainless Steel. Capacity up to 749 lbs/hr, 1000-4600rpm speed range. Approximately 15" x 15" x 10" deep feed hopper, fed by an approximate 2-1/2" diameter x 58" long screw. Driven by a .33hp 3/60/208-230/460 volt, 1725rpm gear motor, 4.88:1 ratio. Approximately 11-1/4" long x 6" wide x 16" deep milling chamber. (16) Fixed blades, Blunt & knife edge 1" wide x 3-3/4" long x 1/2" thick. Driven by a 7.5hp 3/60/230/460 volt, 1760 rpm motor. Approximately 9-1/2" long x 5-1/2" wide bottom discharge, with screen. Mounted on a stainless steel frame with casters. Serial# 7964.

Stock# 11059358

Used Fitzpatrick DAS06 Fitzmill Hammer/Knife Mill. Stainless Steel; Pan Feed; Driven by 7.5 HP, 230/460V, 1740 rpm Explosion Proof (XP) motor. Serial# 10321. Mounted on stainless steel cart with wheels.

Stock# 53844010

Used Fitzpatrick Comminutor Fitzmill, Model D, Stainless Steel. (16) 1" wide x 5/16" thick x 3-3/4" long fixed knives. Approximately 6" diameter x 14" long Cutting chamber. Has gravity feed throat with pan, and bottom screen discharge with 33-1/2" discharge height. Driven by a 10hp, 3/60/208-230/460 volt, 1760 rpm motor. Control panel. Mounted on a carbon steel base with (4) legs and casters.

Stock# 11059356

Used Fitzpatrick FitzMill Hammer Mill, Model DKAS012. Stainless steel; Chute feed; Mounted on wheels. Driven by 15 HP, 1765 rpm, 208-230/460V motor. SN #11170.